ㅤ
TECHNICAL OVERVIEW
KEY PRODUCT SPECIFICATIONS
POST HEIGHT
38.563 in
POST WEIGHT
9 lb
BASE DIAMETER
5.5 in
FLOOR PLATE DIAMETER
5 in
TIP-OVER FORCE
22.5 lbf
EMERGENCY FEATURE
Emergency breakaway belt end supplied standard
SOURCE PRODUCT GRAPHICS
VISUAL REFERENCE
Magnetic-base footprint and floor-plate concept
Magnetic-base queue application
INSTALLATION / ASSEMBLY
SOURCE-BASED PROCEDURE
Condensed for on-page guidance. Use the linked source document below for the complete illustrated procedure, tool list, cautions, and figures.
01
Assess & Prepare
Confirm the floor is flat, smooth, even, and free of abrasions. Sweep and clean the surface; allow it to dry completely.
02
Lay Out the Queue
Use layout lines and measurements to mark the intended center points of the stanchions before any plate is bonded.
03
Clean the Plate Location
Center the floor-plate template over the marked position and clean the exposed mounting area with rubbing alcohol until residue, oil, and chalk are removed.
04
Bond the Floor Plate
Warm the prepared area to about 100°F, remove the adhesive backing, place the stainless-steel plate once, and press it firmly into full contact. The industrial adhesive cannot be repositioned after placement.
05
Allow Full Cure
Apply full pressure across the plate and allow at least 24 hours before attaching a post; the source guide recommends 24–72 hours for best adhesive cure.
06
Attach the Stanchion
After cure, orient the belt, bring the base edge to the plate edge, and rock the magnetic base into controlled contact rather than allowing it to slam onto the plate.
TECHNICAL DOCUMENTS
INSTALLATION & SERVICE RESOURCES
|
PRODUCT GRAPHIC |
15 FT
|
10 FT
|
15 FT
|
10 FT
|
15 FT
|
10 FT
|
10 OR 15 FT
|
10 OR 15 FT
|
10 OR 15 FT
|
10 OR 15 FT
|
|---|---|---|---|---|---|---|---|---|---|---|
| PRODUCT | 7.5" Heavy Duty Magnetic Base - 15 Feet | 7.5" Heavy Duty Magnetic Base - 10 Feet |
5.5" Magnetic Base - 15 Feet
CURRENT PRODUCT
|
5.5" Magnetic Base - 10 Feet | 14" Sloped Base - 15 Feet | 14" Sloped Base - 10 Feet | 14.5" Slim Base | Wall-Mounted Retractable Belt Barrier | Magnetic Wall-Mounted Retractable Belt | Glass/Surface Mount Retractable Belt |
| MOUNT / BASE | 7.5" heavy-duty magnetic floor base | 7.5" heavy-duty magnetic floor base | 5.5" compact magnetic floor base | 5.5" compact magnetic floor base | 14" portable sloped weighted base | 14" portable sloped weighted base | 14.5" portable slim weighted base | Mechanical wall grip connector | Magnetic vertical-surface mount | Adhesive steel plates on glass / smooth surface |
| BELT REACH | 15 ft | 10 ft | 15 ft | 10 ft | 15 ft | 10 ft | 10 or 15 ft | 10 or 15 ft | 10 or 15 ft | 10 or 15 ft |
| BEST WHEN | Long, fixed-geometry queues need maximum magnetic hold | Tighter fixed-geometry queues need maximum magnetic hold | Floor footprint must stay minimal across longer spans | Floor footprint must stay minimal in dense layouts | Portable layouts need wider spans | Portable layouts need tighter turns and spacing | Portable post with slimmer base profile is preferred | Closure repeats in the same location | Closure must move between steel surfaces | Barrier is needed on glass or smooth surfaces |
| PRIMARY BENEFIT | 18 magnets + 28.7 lbf tip-over force; removable post | Heavy magnetic hold + controlled 10-ft geometry | Smallest floor footprint with 15-ft reach | Smallest floor footprint for dense queues | No floor installation; fewer posts over wider spans | Maximum portability for compact layouts | Portable stability with 10/15-ft flexibility | Zero floor footprint; opposing receiver included | Tool-free relocation; no permanent fasteners | Creates magnetic barrier points on glass/smooth surfaces |
Tip: on smaller screens, swipe horizontally to compare all configurations.