ㅤ
TECHNICAL OVERVIEW
KEY PRODUCT SPECIFICATIONS
BELT LENGTH
10 ft or 15 ft
INCLUDED PLATES
Two 3-inch diameter ferrous steel mounting plates
PLATE INSTALLATION
Strong peel-and-stick adhesive
BARRIER MOUNT
Rubber-encased rear magnet
BELT END
Magnetic front belt clip
COMPATIBILITY
Can connect to suitable ferrous surfaces and compatible system receivers
SOURCE PRODUCT GRAPHICS
VISUAL REFERENCE
Escalator / glass-guardrail application
Magnetic glass-mount connection detail
INSTALLATION / ASSEMBLY
SOURCE-BASED PROCEDURE
Condensed for on-page guidance. Use the supplied product information and installation requirements when determining placement.
01
Plan the Barrier Span
Determine where the housing and belt end need to land on the glass or smooth surface and confirm the substrate is appropriate for adhesive mounting.
02
Install the Steel Plates
Apply the two included 3-inch ferrous steel plates to the prepared surfaces using their strong peel-and-stick adhesive.
03
Place the Barrier Housing
Attach the rubber-encased rear magnet to one installed steel plate. The rubber enclosure helps protect the mounting surface.
04
Deploy & Connect
Extend the belt and attach the magnetic front belt clip to the opposing plate, suitable ferrous surface, or compatible system receiver.
No separate glass-mount installation PDF was included in the supplied source set. The setup sequence above is based on the supplied product-page mounting information.
|
PRODUCT GRAPHIC |
15 FT
|
10 FT
|
15 FT
|
10 FT
|
15 FT
|
10 FT
|
10 OR 15 FT
|
10 OR 15 FT
|
10 OR 15 FT
|
10 OR 15 FT
|
|---|---|---|---|---|---|---|---|---|---|---|
| PRODUCT | 7.5" Heavy Duty Magnetic Base - 15 Feet | 7.5" Heavy Duty Magnetic Base - 10 Feet | 5.5" Magnetic Base - 15 Feet | 5.5" Magnetic Base - 10 Feet | 14" Sloped Base - 15 Feet | 14" Sloped Base - 10 Feet | 14.5" Slim Base | Wall-Mounted Retractable Belt Barrier | Magnetic Wall-Mounted Retractable Belt |
Glass/Surface Mount Retractable Belt
CURRENT PRODUCT
|
| MOUNT / BASE | 7.5" heavy-duty magnetic floor base | 7.5" heavy-duty magnetic floor base | 5.5" compact magnetic floor base | 5.5" compact magnetic floor base | 14" portable sloped weighted base | 14" portable sloped weighted base | 14.5" portable slim weighted base | Mechanical wall grip connector | Magnetic vertical-surface mount | Adhesive steel plates on glass / smooth surface |
| BELT REACH | 15 ft | 10 ft | 15 ft | 10 ft | 15 ft | 10 ft | 10 or 15 ft | 10 or 15 ft | 10 or 15 ft | 10 or 15 ft |
| BEST WHEN | Long, fixed-geometry queues need maximum magnetic hold | Tighter fixed-geometry queues need maximum magnetic hold | Floor footprint must stay minimal across longer spans | Floor footprint must stay minimal in dense layouts | Portable layouts need wider spans | Portable layouts need tighter turns and spacing | Portable post with slimmer base profile is preferred | Closure repeats in the same location | Closure must move between steel surfaces | Barrier is needed on glass or smooth surfaces |
| PRIMARY BENEFIT | 18 magnets + 28.7 lbf tip-over force; removable post | Heavy magnetic hold + controlled 10-ft geometry | Smallest floor footprint with 15-ft reach | Smallest floor footprint for dense queues | No floor installation; fewer posts over wider spans | Maximum portability for compact layouts | Portable stability with 10/15-ft flexibility | Zero floor footprint; opposing receiver included | Tool-free relocation; no permanent fasteners | Creates magnetic barrier points on glass/smooth surfaces |
Tip: on smaller screens, swipe horizontally to compare all configurations.